PART NO. SPL.PAGE DESCRIPTION
HZS0403 15.A.7 Screw -cover to engine front plate (3) -(engine unit, 1500)
HZS0403 sup.8 Screw -cover to front plate (3) -(engine unit, sup)
HZS0403 16.A.28 Screw -front cover to mounting plate (3) -(engine unit, 1622)
HZS0404 15.A.6 Screw -blanking plate to cylinder head (heater valve)
HZS0404 15.A.18 Screw -mountings to frame (4) -(rear hanger, exhaust system, 1500)
HZS0404 15.R.16 Screw fixing regulator to mounting bracket (12) -(windows-side, 1500
Coupe)
HZS0404 sup.9 Screw reservoir to crankcase (19) -(engine unit, sup)
HZS0404 16.A.9 Screw -reservoir to crankcase (19) -(engine unit, 1600)
HZS0404 16.A.27 Screw -plate to cylinder head (2) -(heater blanking, engine unit, 1600
and 1600-MK-II)
HZS0404 16.A.30 Screw -reservoir to crankcase (19) -(oil, engine unit, 1622)
HZS0404 16.A3.17 Screw -housing to intermediate mounting (2) -(exhaust system 1622)
HZS0404 16.A3.17 Screw -mounting to frame (4) -(rear, exhaust system 1622)
HZS0404 16.C.2 Screw -case/grille to body (6) -(cooling system, 1600) -alternate for
HPZ0404
HZS0404 16.R.17 Screw -fixing regulator (12) -(windows -side, 1600 and 1600-MK-II
Coupe)
HZS0404 TC.A.16 Screw -clip to bracket -(bypass pipe, water.pipes, Twin Cam)
HZS0404 TC.A.23 Screw -mounting to frame (4) -(intermediate and rear, exhaust system,
Twin Cam)
HZS0404 TC.C.2 Screw -fixing bracket to body (2) -(relief valve, cooling system, Twin
Cam) Com.(E)652 also 575, 613, 623, 633, 648 -was ARH1022
HZS0404 TC.D.2 Screw -earth to pump frame bracket -(fuel system, Twin Cam)
HZS0404 TC.R.16 Screw -fixing regulator (12) -(windows, Coupe, Twin Cam)
HZS0405 15.F.2 Set screw for extension side cover (6) (top cover)
HZS0405 15.M.4 Screw for compensating lever -(parking brake)
HZS0405 15.N.6 Screw for plinth to rear wing (4 for 1500)
HZS0405 15.R.3 Screw fixing s-plate to body (4) -Com.(C)29935 -(body, 1500 T)
HZS0405 15.R.3 Screw fixing rear s-plate to body (8) -(body, 1500 Tourer)
HZS0405 15.R.4 Screw fixing front splash plate to body (4 at top) (body 1500 T)
HZS0405 15.R.7 Srcew fixing front splash plate to body (4 at top) (body 1500 C)
HZS0405 15.R.8 Screw fixing rear s-plate to body (8) -(body, 1500 Coupe)
HZS0405 15.R.18 Set screw for striker pin to lid (2) -(bonnet catch control)
HZS0405 16.A3.18 Screw -brackt to goalpost inner upright, RHD( 4) -(accel.ped.mtg,
1600 and 1600-MK-II) -was HPZ0405
HZS0405 16.A3.18 Screw -brkt to goalpost (R/H) LHD( 4) -(ped and x-shaft assy, 1622)-
was HPZ0405
HZS0405 16.A3.18 Screw -bracket to goalpost (L/H) LHD (3) -(pedal x-shaft assy, 1622)-
was HPZ0405
HZS0405 16.A3.19 Screw -adjustable stop (2) -(pedal shaft assy, 1622)
HZS0405 16.B.2 Screw fixing coil to bracket (2) -(ignition, 1600 standard model)
HZS0405 16.F.1 Screw -side cover to extension (6) (gearbox top cover) -(GB assy,
1600 and 1600-MK-II)
HZS0405 16.M.7 Screw -compensating lever -(handbrake, 1600 and 1600-MK-II)
HZS0405 16.N.3 Screw -bracket to cross member -frame goalpost -RHD (3) -(switches,
1600 and 1600-MK-II)
HZS0405 16.N.10 Screw -plinth to rear wing(4) -(tail, road lamps, 1600) -Fin.(C)100351
HZS0405 16.R.3 Screw fixing splash plate (4) -(front, body shell 1600 and 1600-MK-II
Tourer)
HZS0405 16.R.3 Screw fixing splash plate (12) -(front, body shell 1600 and 1600-MK-II
Tourer)
HZS0405 16.R.3 Screw fixing splash plate (4) -(splash plate rear wing front, body
shell 1600 and 1600-MK-II Tourer)
HZS0405 16.R.4 Screw fixing plate (4) -(splash plate rear wing rear, body, 1600 and
1600-MK-II Tourer)
HZS0405 16.R.7 Screw -fixing plate (4) -(splash plate front wing, body, 1600 and
1600-MK-II Coupe)
HZS0405 16.R.7 Screw -fixing splash plate (12) -(front, body shell 1600 & 1600-MK-II
Coupe)
HZS0405 16.R.8 Screw -fixing plate (4) -(splash rear wing front, body shell 1600 and
1600-MK-II Coupe)
HZS0405 16.R.8 Screw -fixing plate (8) -(splash rear wing front, body shell 1600 and
1600-MK-II Coupe)
HZS0405 16.R.18 Screw -fixing pin (2) -(striker bracket, bonnet fittings, 1600 and
1600-MK-II)
HZS0405 16.R.26 Screw -seat rail to floor (6) -(seats, 1600 and 1600-MK-II)
HZS0405 TC.A.18 Screw -oil cooler to front apron (4) -(oil.cooler, engine, Twin Cam)
HZS0405 16.A3.18 Screw -bracket to goalpost (R/H) (2) -(LHD, eng.controls, Twin Cam)
HZS0405 TC.A.24 Screw -bracket to goalpost (L/H) (3) -(LHD, eng.controls, Twin Cam)
HZS0405 TC.B.2 Setscrew for cable clamp (2) -(ignition, Twin Cam) Com.(E)556
HZS0405 16.F.1 Set screw fixing cover (6) -(top cover,gearbox assy, Twin Cam)
HZS0405 TC.M.4 Screw for compensating lever -(handbrake, Twin Cam)
HZS0405 TC.N.3 Screw bracket to bulkhead RHD (3) -(dipper, switches, electrical,
Twin Cam)
HZS0405 TC.N.8 Screw -plinth to rear wing (4) -(road lamps, electrical, Twin Cam)
HZS0405 TC.R.2 Screw fixing front splash plate (4) -(body shell, Tourer, Twin Cam)
HZS0405 TC.R.3 Screw plate to body (4) -(rear wing front, body shell, Tourer, Twin
Cam)
HZS0405 TC.R.3 Screw fixing rear splash plate (8) -(rear wing rear, body shell,
Tourer, Twin Cam)
HZS0405 TC.R.5 Screw fixing front splash plate (4) -(body shell, Coupe, Twin Cam)
HZS0405 TC.R.7 Screw -plate to body (4) -(rear wing forward splash, body shell,
Coupe, Twin Cam)
HZS0405 TC.R.7 Screw fixing rear splash plate (8) -(body shell, Coupe, Twin Cam)
HZS0405 TC.R.18 Screw fixing pin -(striker pin assy, bonnet fittings, Twin Cam)
HZS0405 TC.R.57 Screw (2) -(heat+vent equip, Twin Cam)
HZS0406 15.A.7 Screw -cover to main bearing cap (2)
HZS0406 15.A.12 Screw -cooling fan to pulley hub
HZS0406 15.B.1 Clamp bolt -bracket -(coil, ignition, 1500)
HZS0406 15.O.3 Screw for oil pipe connector to starter bracket -(engine unit, 1500)
HZS0406 sup.8 Screw -front cover to bearing cap (2) -(engine unit, sup)
HZS0406 16.A.7 Screw -front cover to bearing cap (2) -(engine unit, 1600)
HZS0406 16.A.13 Screw -fan to pulley (4) -(w-pump, engine unit, 1600)
HZS0406 16.A.28 Screw -front cover to bearing cap (2) -(engine unit, 1622)
HZS0406 16.A.33 Screw -fan to pulley (4) -(water pump, engine unit, 1622)
HZS0406 16.A.35 Screw -cooler to front apron (4) -(engine unit, 1622)
HZS0406 16.O.1 Screw -connector to starter bracket -(oil pipe, instruments, 1600 and
1600-MK-II)
HZS0406 16.Q.1 Screw toeboard plate to goalpost (9) -(chassis frame, 1600 and
1600-MK-II) -was HPZ0406
HZS0406 16.R.46 Screw -water valve (short) -(heater, 1600 and 1600-MK-II)
HZS0406 TC.A.18 Screw -clip to support bracket -(cooler pipes, oil.cooler, engine,
Twin Cam)
HZS0406 TC.O.2 Screw -connector to starter bracket -(oil pipes, instruments, Twin
Cam)
HZS0407 15.F.5 Set screw for front and rear levers (2) (remote control shaft)
HZS0407 15.N.8 Screw -horn to bracket (R/H standard)
HZS0407 15.N.8 Screw -horn to bracket (L/H standard)
HZS0407 16.F.5 Screw -selector lever (2)-(remote control, gbx, 1600 and 1600-MK-II)
HZS0407 16.H.8 Bolt -keep plate (2) -(pad, caliper assy, rear axle, ARDB model 1600
and 1600-MK-II) -Com.(C)92104
HZS0407 16.N.12 Screw -horn to bracket (2) -(R/H front extension, 1600 and 1600-MK-II)
HZS0407 16.N.12 Screw -horn to bracket (2) -(L/H front extension, 1600 and 1600-MK-II)
HZS0407 16.R.46 Screw -water valve (long) -(heater, 1600 and 1600-MK-II)
HZS0407 TC.A.13 Screw -sump to crankcase) (19) -(sump, engine, Twin Cam)
HZS0407 TC.F.6 Screw -sfront and rear lever) (2) -(remote control, gearbox, Twin Cam)
HZS0407 TC.H.3 Bolt for keep plate (2) -(caliper assy, rear axle, Twin Cam)-
Com.(C)836 approx. -was 7H8204
HZS0407 TC.K.2 Bolt for keep plate (2) -(caliper assy, front axle, Twin Cam)-
Com.(C)836 approx. -was 7H8204
HZS0407 TC.N.10 Screw -horn to bracket (2) -(R/H front extension, low note, flasher-
horn controls, electrical, Twin Cam)
HZS0407 TC.N.10 Screw -horn to bracket (2) -(L/H to front extension, high note,
flasher-horn controls, electrical, Twin Cam) -optional extra
HZS0408 TC.A.13 Screw for cover (short) -(oil.pump, sump, engine, Twin Cam)
HZS0414 TC.A.13 Screw for cover (long) -(oil.pump, sump, engine, Twin Cam)
HZS0416 16.B.2 Screw -clamp (fixing coil to bracket, 1600 all round disc brakes
model) -Com.(C)91240
HZS0473 TC.A.18 Screw -blade to pulley (4) -(fan, engine, Twin Cam)
HZS0504 15.K.3 Scew -check rubber to member (2) -(front suspension, 1500)
HZS0504 15.M.4 Screw for hand brake to gearbox cover -(5)
HZS0504 15.N.10 Screw -battery cable to earth
HZS0504 16.J.4 Screw -column to upper bracket -(adj.steering column, steering 1600
and 1600-MK-II) -when steering lock is fitted
HZS0504 16.K.4 Screw -check rubber to member(2) -(front suspension, 1600 and
1600-MK-II std.model)
HZS0504 16.M.7 Screw -handbrake to gearbox cover(5) -(handbrake, 1600 and 1600-MK-II)
HZS0504 16.N.15 Screw -battery cable to earth -(cables and connections, 1600 and
1600-MK-II)
HZS0504 TC.K.3 Screw -Check rubber to cross member (2) -(front suspension, Twin Cam)
HZS0504 TC.M.4 Screw -hand brake to gearbox cover (5) -(handbrake, Twin Cam)
HZS0504 TC.N.12 Screw -battery cable to earth -(cables and connections, electrical,
Twin Cam)
HZS0505 16.M.7 Screw -handbrake to gearbox cover(3) -(handbrake, 1600 and 1600-MK-II)
HZS0505 15.A.18 Screw -strap to front pipe -(mtg.exh front, exhaust system, 1500)
HZS0505 15.D.3 Screw -front mounting (2) -(fuel tank, 1500)
HZS0505 15.H.5 Screw for bump rubber to frame (4)
HZS0505 15.J.3 Screw for seal and retainer to dash (1) (2 lengths, see HZS0506)
HZS0505 15.J.3 Screw for blanking plate and seal (2) (passenger side steering hole)
HZS0505 15.K.4 Screw -housing to member (4) -(bush, anti-roll bar to frame, 1500)-
optional extra
HZS0505 15.M.1 Screw for box to bulkhead -(4 master cylinder box)
HZS0505 15.M.3 Screw for 3-way piece and clip t0 axle bracket
HZS0505 15.M.4 Screw for hand brake to gearbox cover -(3)
HZS0505 15.N.8 Screw -horn bracket to R/H front extension (2 standard)
HZS0505 15.N.8 Screw -horn bracket to L/H front extension (2 optional)
HZS0505 15.R.19 Screw fixing lamp bracket to mounting bracket (2) -(rear number plate)
HZS0505 16.A.16 Screw -mounting rubber and coil bracket to frame bracket (4)-
(eng.mtg, eng.unit, 1600) -Com.(C)91240. all round disc brakes model)
HZS0505 16.A3.17 Screw -strap to front pipe -(exhaust system 1622)
HZS0505 16.D.3 Screw -front mounting (2) -(fuel tank, 1600)
HZS0505 16.H.10 Screw -bump rubber to frame (4) -(rear spring, 1600 and 1600-MK-II)
HZS0505 16.J.3 Screw -bracket to body rail (2) -(steering, 1600 and 1600-MK-II)
HZS0505 16.J.3 Screw -retainer to dash -(at bulkhead, steering, 1600 and 1600-MK-II)
HZS0505 16.J.3 Screw -blanking plate to dash (2) -(steering, 1600 and 1600-MK-II)
HZS0505 16.K.5 Screw -fixing housing (4) -(bush, anti-roll bar to frame, 1600 and
1600-MK-II std.model) -optional extra
HZS0505 16.M.1 Screw -box to bulkhead (4) -(m/c, brake controls, std.model, 1600 and
1600-MK-II)
HZS0505 16.M.2 Screw -bracket to tapping plate (4) -(brake controls, ARDB model 1600
and 1600-MK-II) Com.(C)91240
HZS0505 16.M.5 Screw -3-way piece to bracket -(hyd.pipes +fittings, 1600 and
1600-MK-II)
HZS0505 16.N.12 Screw -horn bracket to R/H front extension (2) -(low note, 1600 and
1600-MK-II)
HZS0505 16.N.12 Screw -horn bracket to R/H front extension (2) -(low note, 1600 and
1600-MK-II)
HZS0505 16.N.12 Screw -horn bracket to L/H front extension (2) -(high note, 1600 and
1600-MK-II)
HZS0505 16.R.7 Screw -front wing to body (21) -(body shell, 1600 & 1600-MK-II Coupe)
HZS0505 16.R.19 Screw -lamp bracket to mounting bracket (2) -(number plate, rear, 1600
and 1600-MK-II
HZS0505 TC.A.7 Bolt -clip to crankcase -(vent.pipe.clip, engine, Twin Cam) Fin.(E)656
HZS0505 TC.A.8 Screw -hub to engine front plate (2) -(chain idler sprocket, camshaft,
engine, Twin Cam)
HZS0505 TC.A.22 Screw -mounting rubber to bracket (R/H) (4) -(engine mounting, Twin
Cam)
HZS0505 TC.A.23 Screw -strap to front pipe -(exhaust system, Twin Cam)
HZS0505 TC.B.1 Screw fixing coil to body panel (2) -(ignition, Twin Cam)
HZS0505 TC.H.5 Screw -bump rubber to frame (4) -(rear spring, Twin Cam)
HZS0505 TC.J.3 Screw -retainer to dash -(at bulkhead, steering, Twin Cam)
HZS0505 TC.J.3 Screw -blanking plate to dash (2) -(pass.side steering hole in
bulkhead, steering, Twin Cam)
HZS0505 TC.K.4 Screw -housing to member (4) -(rubber bush, anti-roll bar, Twin Cam)-
Com.(C)2275
HZS0505 TC.M.1 Screw -bracket to tapping plate (4) -(support brackets, brake
controls, Twin Cam)
HZS0505 TC.M.4 Screw -hand brake to gearbox cover (3) -(handbrake, Twin Cam)
HZS0505 TC.N.10 Screw -horn bracket to L/H front extension (2) -(high note, flasher
horn controls, electrical, Twin Cam) -optional extra
HZS0505 TC.R.19 Screw -lamp bracket to mounting bracket (2) -(rear, number plates and
fittings, Twin Cam)
HZS0506 TC.A.22 Screw -mounting rubber to bracket (L/H) (4) -(engine mounting, Twin
Cam)
HZS0506 15.A.7 Screw -mounting plate to crankcase
HZS0506 15.A.7 Screw -vent pipe to crankcase [Com (E)GD101]
HZS0506 15.A.7 Screw -cover to crankcase (4)
HZS0506 15.A.7 Screw -rear plate to crankcase (4)
HZS0506 15.A.11 Screw -water pump body to crankcase (short)
HZS0506 15.A.12 Screw -bracket to crankcase -(Dynamo mounting, 1500)
HZS0506 15.A.17 Screw -mounting rubber to frame brackets (8) -(engine mounting)
HZS0506 15.D.7 Set screw for cleaner to carburetors (4) -(air cleaner, 1500)
HZS0506 15.J.1 Screw for bearing to steering box (2) -(steering, 1500)
HZS0506 15.J.3 Screw for bracket to frame (2) (steering column clamp lower)
HZS0506 15.J.3 Screw for seal and retainer to dash (1) (2 lengths, see HZS0505)-
(steering, 1500)
HZS0506 15.M.1 Screw for cover -(2 blanking piece)
HZS0506 15.M.1 Screw -pedal box to bracket -rear -(2)
HZS0506 15.M.1 Screw -bracket to tapping plate -(4 pedal support brackets L&R)
HZS0506 15.M.1 Screw -bracket to base plate -(2 pedal support brackets L&R)
HZS0506 15.N.7 Screw -bracket to bumper blade (lower) (2 for fog brackets optional)
HZS0506 sup.8 Screw -cover and front plate to crankcase (4) -(engine unit, sup)
HZS0506 sup.11 Screw -bracket to crankcase (2) -(dynamo +dist.mtg, engine unit, sup)
HZS0506 16.A.2 Screw -mounting plate to crankcase (2) -(engine unit, 1600)
HZS0506 16.A.7 Screw -front cover to mtg plate and crankcase (4) -(engine unit, 1600)
HZS0506 16.A.11 Screw -bracket to crankcase (2) -(dynamo, engine unit, 1600)
HZS0506 16.A.16 Screw -mounting rubber to frame bracket (5) -(eng.mtg, eng,unit, 1600)
HZS0506 16.A.16 Screw -mounting rubber to frame bracket (4) -(eng.mtg, eng.unit,1600)-
Com.(C)91240, all round disc brakes model)
HZS0506 16.A.23 Screw -mounting plate to crankcase (3) -(eng.mtg, eng.unit, 1622)
HZS0506 16.A.28 Screw -front cover to mounting plate crankcase (4) -(eng.unit, 1622)
HZS0506 16.A.31 Screw -bracket to crankcase (2) -(dynamo rear, engine unit, 1622)
HZS0506 16.D.7 Screw -Cleaner to carburetor (2) -(carburetors, engine unit, 1600)
HZS0506 16.J.1 Screw -bearing to rack housing (2) -(steering, 1600 and 1600-MK-II)
HZS0506 16.J.3 Screw -Bracket to frame (2) -(steering column, 1600 and 1600-MK-II)
HZS0506 16.J.3 Screw -retainer to dash -(at bulkhead, steering, 1600 and 1600-MK-II)
HZS0506 16.M.1 Screw -fixing cover (2) -(blanking piece, brake controls, std.model,
1600 and 1600-MK-II)
HZS0506 16.M.1 Screw -box to bracket (rear) (2) -(brake controls, std.model, 1600 and
1600-MK-II)
HZS0506 16.M.1 Screw -bracket to tapping plate (4) -(brake controls, std.model, 1600
and 1600-MK-II)
HZS0506 16.M.1 Screw -bracket to base plate (2) -(brake controls, std.model, 1600 and
1600-MK-II)
HZS0506 16.M.3 Screw -fume excluder, cover plate and base plate to cross bar (2)-
(brake controls, ARDB model 1600 and 1600-MK-II) Com.(C)91240
HZS0506 16.M.2 Screw -box to bulkhead (2) -(brake controls, ARDB model 1600 and
1600-MK-II) Com.(C)91240
HZS0506 16.M.2 Screw -box to bracket (6) -(brake controls, ARDB model 1600 and
1600-MK-II) Com.(C)91240
HZS0506 16.M.6 Screw -3-way connection and cable clip to rear axle -(hyd.pipes
+fittings, ARDB model 1600 and 1600-MK-II) -Com.(C)91240
HZS0506 16.N.9 Screw bracket to bumper blade (lower) (2) -(fog lamp optional, road
lamps, 1600 and 1600-MK-II)
HZS0506 16.Q.2 Screw -body to goal post cross-bar (3) -(body mounting, 1600 and
1600-MK-II)
HZS0506 16.Q.2 Screw -body to goal post cross-bar (3) -(body mounting, 1600 and
1600-MK-II)
HZS0506 16.Q.2 Screw -body to 4th cross-member (2) -(body mounting, 1600 and
1600-MK-II)
HZS0506 16.R.43 Bolt -(sundries, 1600 and 1600-MK-II) -for BHA4066 mirror
HZS0506 TC.A.8 Screw -damper bracket to engine front plate (4) -(chain, camshaft,
engine, Twin Cam)
HZS0506 TC.C.2 Screw -fixing bracket to exhaust manifold (2) -(header tank,
cooling system, Twin Cam)
HZS0506 TC.C.2 Screw -air cleaner to carburetor (4) -(air cleaner, Twin Cam) -changed
to HS0507 Com.(C)2468
HZS0506 TC.J.1 Screw -bearing to steering box (2) -(rack assy, steering, Twin Cam)
HZS0506 TC.J.2 Screw -bracket to frame (2) -(lower column, steering, Twin Cam)
HZS0506 TC.J.3 Screw -retainer to dash -(at bulkhead, steering, Twin Cam)
HZS0506 16.M.1 Screw -cover plate to base plate (2) -(fume excluder, brake controls,
Twin Cam)
HZS0506 TC.M.1 Screw -box to bulkhead (2) -(pedal box, brake controls, Twin Cam)
HZS0506 TC.M.1 Screw -box to bracket (6) -(pedal box, brake controls, Twin Cam)
HZS0506 TC.M.1 Screw fixing blanking plate (2) -(brake controls, Twin Cam)
HZS0506 TC.M.2 Screw -3-way connection and cable clip to axle -(brake controls, Twin
Cam)
HZS0506 TC.N.9 Screw -bracket to bumper blade (lower)(2) -(fog lamp, road lamps,
electrical, Twin Cam) -optional
HZS0506 TC.R.54 Bolt (2) -(stem assy, sundries, Twin Cam) -for BHA4066 mirror -optional
HZS0507 15.A.17 Screw -bracket to mounting plate -R/H (2) -(engine mounting, 1500)
HZS0507 15.C.1 Screw for block to body -(cooling system, 1500)
HZS0507 15.E.1 Screw for clutch to flywheel (6) -(clutch, 1500)
HZS0507 15.K.3 Screw -spring pan to wishbone (4)
HZS0507 15.M.1 Screw -pedal box to bracket -front -(2)
HZS0507 16.A.16 Screw -mounting rubber and coil bracket to frame bracket(3) -(eng.mtg,
engine unit,1600)- (standard model)
HZS0507 16.C.1 Screw fixing core to body (6) -(radiator to body, cooling.sys, 1600)
HZS0507 16.E.1 Screw -clutch to flywheel (6) -(clutch assembly, 1600)
HZS0507 16.K.4 Screw -spring pan to wishbone (4) -(front suspension, 1600 and
1600-MK-II std.model)
HZS0507 16.M.1 Screw -box to bracket (front) (2) -(brake controls, std.model, 1600
and 1600-MK-II)
HZS0507 TC.D.5 Screw -fixing air cleaner (4) -(late style air cleaner, Twin Cam)-
Com.(C)2468 -prior to (C)2468 always supply 4 off HZS0507 with 2 off AHH5960 air
cleaners -was HZS0506
HZS0507 TC.A.6 Screw -plate to crankcase (4) -(rear.eng.plate, engine, Twin Cam)
HZS0507 TC.C.1 Screw for block (6) -(radiator to body, cooling system, Twin Cam)
HZS0507 TC.K.3 Screw -spring pan to wishbone (4/2) -(front suspension, Twin Cam)-
quantity reduced at (C)2257
HZS0508 15.J.2 Screw for rack to bracket -rear (2) -(steering, 1500)
HZS0508 15.K.3 Screw -spring pan to wishbone (4)
HZS0508 16.A.16 Screw -bracket to mount plate -R/H (2) -(engine mounting, 1600)
HZS0508 16.A.23 Bolt -eng.mt.bracket to plate -R/H top -(engine mounting, 1622)
HZS0508 16.J.2 Bolt -rack to bracket -rear (2) -(steering, 1600 and 1600-MK-II)
HZS0508 16.K.4 Screw -spring pan to wishbone (4) -(front suspension, 1600 and
1600-MK-II std.model)
HZS0508 16.M.1 Screw -base plate to cross bar (2) -(brake controls, std.model, 1600
and 1600-MK-II)
HZS0508 16.M.1 Screw -fixing cover (2) -(blanking piece, brake controls, std.model,
1600 and 1600-MK-II)
HZS0508 16.Q.2 Screw -body (10) -(body mounting, 1600 and 1600-MK-II)
HZS0508 16.Q.2 Screw -body to goal post cross-bar end (2) -(body mounting, 1600 and
1600-MK-II)
HZS0508 16.Q.2 Screw -body to shut pillar front/rear brackets (8) -(body mounting,
1600 and 1600-MK-II)
HZS0508 16.R.2 Screw fixing front wing to body (21) -(body shell, 1600 & 1600-MK-II)
HZS0508 16.R.7 Screw -rear wing to body (22) -(body shell, 1600 & 1600-MK-II Coupe
HZS0508 TC.A.10 Screw -timing case to engine front plate (1" long) (5) -(camshaft,
engine, Twin Cam)
HZS0508 TC.A.15 Screw -body to scroll (2) -(water.pump, engine, Twin Cam)
HZS0508 TC.A.16 Screw -pipe to water pump (2) -(water.pipes, engine, Twin Cam)
HZS0508 TC.A.16 Screw -housing to engine front plate (2) -(thermostat, water.pipes,
Twin Cam)
HZS0508 TC.A.18 Screw -bracket to engine front plate (2) -(cooler pipes, oil.cooler,
engine, Twin Cam)
HZS0508 TC.A.22 Screw -bracket to mounting plate (2) -(engine mounting, Twin Cam)
HZS0508 TC.A.23 Screw for clip -(connector pipe, exhaust system, Twin Cam)
HZS0508 TC.J.2 Bolt -rack to bracket (rear) (2) -(steering, Twin Cam)
HZS0508 TC.K.3 Screw -spring pan to wishbone (4) -(front suspension, Twin Cam)
HZS0508 TC.R.35 Screw -bracket fixing (4) -(quick release, early Seat Belts, Twin Cam)
HZS0508 TC.R.35 Screw -bracket fixing (4) -(quick release, late Seat Belts, Twin Cam)
HZS0509 15.A.11 Screw -water pump body to crankcase (short) (2) -(1500)
HZS0509 sup.11 Screw -pump to crankcase -short (2) -(water, engine unit, sup)
HZS0509 16.A.11 Screw -pump to crankcase (short) (2) -(w.pump, 1H1149, eng.unit, 1600)
HZS0509 16.A.31 Screw -pump to crankcase (short) (2) -(water, engine unit, 1622)
HZS0509 16.A.32 Bolt -dynamo to mounting bracket -(rear, engine unit, 1622)
HZS0509 16.J.2 Bolt -rack to bracket -front (2) -(steering, 1600 and 1600-MK-II)
HZS0509 TC.A.10 Bolt -timing case to engine front plate and crankcase (1-1/8" long)(3)
-(camshaft, engine, Twin Cam) -was HBN0509
HZS0510 16.E.4 Bolt -fixing cylinder -(master cyl, clutch controls, AWDB model 1600)
HZS0510 16.M.4 Screw fixing master cylinder (2) -(brake master cylinder, ARDB model
1600 and 1600-MK-II) Com.(C)91240
HZS0510 16.Q.2 Screw -body to shut pillar (2) -(body mounting, 1600 and 1600-MK-II)
HZS0510 16.R.2 Screw fixing front wing to body (5) -(body shell, 1600 and 1600-MK-II)
HZS0510 16.R.7 Screw -front wing to body (5) -(body shell, 1600 and 1600-MK-II Coupe)
HZS0510 TC.E.1 Bolt -fixing cylinder (2) -(master.cyl.assy, clutch, Twin Cam)
HZS0513 TC.M.2 Bolt -fixing master cylinder (2) -(brake master cylinder, Twin Cam)-
changed to HZS0510 Com.(C)997
HZS0515 TC.D.3 Screw -front mounting (2) -(fuel tank, Twin Cam)
HZS0606 15.A.17 Screw -bracket to block (2) -(engine mounting)
HZS0606 15.Q.1 Screw for extension to frame bracket (8) -(chassis frame, 1500)
HZS0606 16.A.16 Screw -bracket to block (2) -(engine mounting, 1600)
HZS0606 16.Q.1 Screw -extension to frame bracket (8) -(chassis frame, 1600 and
1600-MK-II)
HZS0606 TC.A.22 Screw -bracket to block (2) -(engine mounting, Twin Cam)
HZS0606 TC.Q.1 Screw -extension to frame bracket (8) -(chassis frame, Twin Cam)
HZS0607 TC.A.6 Screw -plate to crankcase (8) -(rear.eng.plate, engine, Twin Cam)
|