PART NO. SPL.PAGE DESCRIPTION
3H544 15.E.2 Banjo for slave cylinder -(clutch, 1500) -Fin.(C)11767
3H544 15.M.2 Banjo -master cylinder -(for clutch pipe)
3H544 16.M.3 Banjo -master cylinder -(for clutch pipe) -(std.model 1600 and
1600-MK-II)
3H547 15.E.2 Bolt for banjo to slave cylinder -(clutch, 1500) -Fin.(C)11767
3H547 15.M.2 Bolt -banjo -(master cylinder clutch pipe)
3H547 16.M.3 Bolt -banjo -(master cylinder, std.model 1600 and 1600-MK-II) -changed
to 11K8276
3H549 16.M.3 Joint -banjo bolt connection (lower) -(master cylinder, std.model 1600
and 1600-MK-II) -changed to 7H7456
3H550 15.E.2 Joint for banjo -(slave cylinder, clutch, 1500) -Fin.(C)11767
3H550 15.H.4 Joint for banjo connection (large) (2) (rear brake banjo)
3H550 15.M.2 Joint for banjo connection -(upper, master cylinder clutch pipe)
3H550 16.E.2 Joint -clutch hose -(at clutch hose on chassis, clutch controls, 1600)
3H550 16.H.4 Gasket -banjo connection (large)(2) -(rear drum brakes, 1600 and
1600-MK-II)
3H550 16.M.3 Joint -banjo connection -(upper, master cylinder, std.model 1600 and
1600-MK-II)
3H550 16.M.5 Gasket -front brake hose (2) -(hyd.pipes +fittings, std.model 1600 and
1600-MK-II)
3H554 15.E.2 Bleeder screw -(slave cylinder, clutch, 1500)
3H554 16.E.2 Screw -bleeder -(clutch.op.cylinder, 1600)
3H576 15.A.7 Tap -water drain -(engine unit, 1500)
3H576 sup.8 Tap -cylinder drain -(engine unit, sup)
3H576 16.A.2 Tap -cylinder block drain -(engine unit, 1600)
3H576 TC.A.1 Tap -water drain -(cyl.block assy, engine, Twin Cam)
3H868 16.E.4 Banjo -(clutch.op.cyl, clutch controls, ARDB model 1600) -Com.(C)91240
3H868 TC.E.2 Banjo -(slave cylinder, clutch, Twin Cam)
3H876 16.E.3 Joint -clutch hose -(clutch controls, ARDB model 1600) -Com.(C)91240
3H876 TC.E.1 Gasket, hose to pipe -(Cu washer, slave hose to banjo,
master.cyl.assy, clutch, Twin Cam)
3H914 15.O.3 Bulb holder -fuel gauge and oil and temperature gauge (2)
3H914 TC.O.2 Bulb holder -(oil and temperature gauge illumination, instruments,
Twin Cam) -changed to 37H5181
3H914 TC.O.2 Bulbholder -(fuel gauge illumination, instruments, Twin Cam)-
correction, changed to 37H5181
3H921 15.N.5 Bulb -vertical dip (2) -changed to 13H138 om.(C)58918
3H949 15.N.3 Switch -starter -(switches, 1500)
3H949 16.N.3 Switch -starter -(switches, 1600 and 1600-MK-II)
3H949 TC.N.3 Switch -starter -(switches, Twin Cam)
3H950 15.A.21 Connector coupling -starter pull mounting)
3H950 15.N.3 Coupling -switch to control -(starter switch, eng.control, 1500)
3H950 16.A3.20 Coupling -switch to control -(starter, switches, 1600 and 1600-MK-II)
3H950 TC.A.26 Coupling -starter pull connector -(starter control, Twin Cam)
3H950 TC.N.3 Coupling -starter switch to control -(switches, Twin Cam)
3H952 16.N.2 Starter -(starter, 1600 and 1600-MK-II) -changed to 13H559-
Com.(E)16GC/H6435
3H952 TC.N.2 Starter -(starter, Twin Cam)
3H999 15.O.1 Sleeve (rubber) -(flasher warning light bulb holder)
3H999 TC.N.10 Sleeve (rubber) -(flasher warning light bulb holder, flasher-horn
controls, electrical, Twin Cam) -changed to ACG5185
3H999 TC.R.53 Sleeve (rubber) -(bulb holder, map light, facia panel, Twin Cam)
3H1031 15.N.5 Gasket -rubber (2) (headlight to body, 1500)
3H1031 16.N.5 Gasket -body (2) -(rubber, headlamp Sweden, road lamps, 1600 and
1600-MK-II) -Com.(C)72040
3H1031 16.N.6 Gasket -body (2) -(headlamp LHD Europe except France, road lamps, 1600
and 1600-MK-II)
3H1031 16.N.6 Gasket -body (2) -(headlamp LHD Europe except France, road lamps, 1600
and 1600-MK-II) -changed to BFS410
3H1031 16.N.6 Gasket -body (2) -(headlamp, France, road lamps, 1600 and 1600-MK-II)
3H1031 16.N.7 Gasket -body (2) -(headlamp LHD except Europe, road lamps, 1600 and
1600-MK-II)
3H1031 TC.N.5 Gasket -rubber (2) -(headlamp UK LHD -(road lamps, electrical, Twin
Cam)
3H1031 TC.N.5 Gasket -rubber (2) -(headlamp Sweden, road lamps, electrical, Twin
Cam) Com.(C)2418
3H1031 TC.N.5 Gasket -rubber (Europe LHD) (2) -(headlmp, road lamps, electrical,
Twin Cam) -changed to BFS410
3H1031 TC.N.6 Gasket -rubber (France LHD) (2) -(headlmp, road lamps, electrical,
Twin Cam)
3H1031 TC.N.6 Gasket -rubber (not UK, LHD except Europe) (2) -(headlmp, road lamps,
electrical, Twin Cam)
3H1031 TC.N.6 Gasket -body (USA, LHD) (2) -(headlmp, road lamps, electrical, Twin
Cam) Com.(C)2278
3H1422 15.B.1 Suppressor -ignition cables (4) -(distibutor, ignitiom, 1500)
3H1422 TC.B.2 Suppressor -ignition cables (4) -(ignition, Twin Cam)
3H1454 15.N.8 Relay unit -flasher lights -(1500)
3H1454 TC.N.10 Relay unit -flasher -(flasher-horn controls, electrical, Twin Cam)-
Fin.(C)2192
3H1457 16.N.14 Grommet (1) -(bulkhead, cables and connections, 1600 and 1600-MK-II)
3H1709 TC.G.1 Lubrictor -yoke sleeve -(propshaft, Twin Cam)
3H1813 15.N.6 Number plate lamp -(road lamps, 1500)
3H1813 TC.N.7 Number plate lamp -(road lamps, Twin Cam)
3H1835 15.N.4 Box -control -(switches, 1500)
3H1835 16.N.4 Box -control -(switches, 1600 and 1600-MK-II) -changed to 3H1836-
Com.(E)16GA/H6272
3H1835 TC.N.4 Box -control -(switches, electrical, Twin Cam)
3H1836 16.N.4 Box -control -(switches, 1600 and 1600-MK-II) Com.(E)16GA/H6272 -was
3H1835
3H1893 15.N.5 Bulb -right dip (2 for LHD)
3H1893 TC.N.6 Bulb -right dip, not UK, LHD except Europe (2) -(headlamp, road lamps,
electrical, Twin Cam -changed to BFS355
3H1894 15.N.3 Switch -stop lamp (pressure switch)
3H1894 16.N.3 Switch -stop lamp -(pressure, switches, 1600 and 1600-MK-II)
3H1894 TC.N.3 Switch -stop lamp -(pressure, switches, electrical, Twin Cam)
3H1911 15.N.4 Relay -headlamp flasher (N. American LHD) -(switches, 1500)
3H1911 16.N.4 Relay -headlamp flasher (N. American LHD) -(switches, 1600 and
1600-MK-II)
3H1911 TC.N.4 Relay -headlamp flasher (N. American LHD) -(switches, electrical,
Twin Cam) -optional extra
3H2006 15.A.6 Plug -sparking (4) -(engine unit, 1500)
3H2006 sup.7 Plug -sparking (4) -(engine unit, sup)
3H2006 16.A.6 Plug -sparking (4) -(engine unit, 1600)
3H2006 16.A.27 Plug -sparking (4) -(engine unit, 1622)
3H2098 15.A.12 Screw for adjusting link to dynamo (engine unit, 1500)
3H2098 16.A.12 Screw -adjusting link to pillar -(dynamo, engine unit, 1600)
3H2098 TC.A.17 Screw -link to dynamo -(dist+dynamo mountings, engine, Twin Cam)-
Fin.(E)111 except 103, 106, 109 -for all replacements use ZCS0509 with 2A110 PW205
and 51K1712
3H2138 15.B.1 Plate -clamping -(distributor, ignition, 1500)
3H2138 16.B.1 Plate -clamping -(distributor, ignition, 1600)
3H2138 16.B.2 Plate -clamping -(distributor, ignition, 1600) Com.(E)16GC/H101
3H2138 TC.B.1 Plate -clamping -(distributor, ignition, Twin Cam) -for all service
replacements AEJ41 distributor must be used see service memo MG301
3H2287 15.H.4 Joint for banjo connection (small) (2) (rear brake banjo)
3H2287 15.M.2 Joint for adapter -(master cylinder clutch pipe)
3H2287 15.M.3 Joint for brake hose (3) -(hydraulics, 1500)
3H2287 16.H.4 Gasket -banjo connection (small)(2) -(rear drum brakes, 1600 and
1600-MK-II)
3H2287 16.M.3 Joint -adapter -(master cylinder, std.model 1600 and 1600-MK-II)
3H2287 16.M.5 Gasket -brake hose (front and rear)(3) -(hyd.pipes +fittings,
std.model 1600 and 1600-MK-II)
3H2287 16.M.6 Gasket -rear hose to 3-way -(hyd.pipes +fittings, ARDB model 1600 and
1600-MK-II) Com.(C)91240
3H2287 TC.M.2 Gasket -rear hose to 3-way -(hyd.pipes+fittings, Twin Cam)
3H2424 15.M.3 Three-way piece for rear axle -Com.(C)27989 (disc wheels),
(C)28540 (wire wheels) -was AJA5028
3H2424 16.M.5 Three-way piece -rear axle -(hyd.pipes +fittings, 1600 and 1600-MK-II)
3H2428 15.H.4 Screw -bleeder (2) -(rear drum brakes, 1500)
3H2428 15.K.2 Screw -bleeder (2) -(front drum brakes, 1500)
3H2428 16.H.3 Screw -bleeder (2) -(rear drum brakes, 1600 and 1600-MK-II)
3H2428 16.K.3 Screw -bleed (4) -(caliper, front brakes, 1600 and 1600-MK-II
std.model)
3H2520 15.N.5 Headlamp -vertical dip (2 not for U.K.) -
change to BCA4302 Com.(C)58918
3H2520 TC.N.5 Headlamp (Europe LHD, except France) (2) -(road lamps, electrical,
Twin Cam) -Fin.(C)823
3H2521 TC.N.6 Headlamp (less bulb) (France LHD) (2) -(road lamps, electrical,
Twin Cam) -Fin.(C)1617 -was 17H5330
3H2648 15.S.1 Screwdriver -distributor and gauge -(tool kit, 1500)
3H2648 16.S.1 Screwdriver -distributor and gauge (feeler .015") -(tool kit, 1600
and 1600-MK-II) -Fin.(C)93547 -changed to 97H2724
3H2648 TC.S.1 Screwdriver and gauge -distributor (feeler .015") -(tool kit, Twin
Cam)
3H2695 15.B.1 Nut -terminal -(coil HT connection, ignition, 1500)
3H2695 16.B.2 Nut -terminal -(coil HT connection, ignition, 1600)
3H2695 TC.B.1 Nut -terminal -(ignition, Twin Cam)
3H2696 15.B.1 Washer for nut -(coil HT connection, ignition, 1500)
3H2696 16.B.2 Washer for nut -(coil HT connection, ignition, 1600)
3H2695 TC.B.1 Washer for nut -(coil HT terminal, ignition, Twin Cam)
3H2825 16.N.3 Switch -ignition -(switches, 1600 and 1600-MK-II) -was AHH5369
3H2865 15.F.4 Bearng -needle roller -for layshaft (3) -(gearbox, 1500)
3H2865 16.F.3 Roller -needle bearing -layshaft (3) -(gearbox, 1600 and 1600-MK-II)
3H2865 TC.F.4 Bearing -needle roller (3) -(layshaft, gearbox, Twin Cam)
3H2914 15.E.1 Spring for pressure plate (6) -(clutch, 1500) -change to 1H1024
Com.(E)GB16225
3H2962 15.N.5 Excluder -dust(2) -(headlamp, road lamps, 1500)
3H2962 16.N.5 Excluder -dust(2) -(headlamp, road lamps, 1600 and 1600-MK-II)
3H2962 16.N.5 Excluder -dust(2) -(headlamp Sweden, road lamps, 1600 and 1600-MK-II)-
Com.(C)72040
3H2962 16.N.6 Excluder -dust(2) -(headlamp LHD Europe except France, road lamps,
1600 and 1600-MK-II)
3H2962 16.N.6 Excluder -dust (2) -(headlamp France, road lamps, 1600 and 1600-MK-II)
3H2962 16.N.7 Excluder -dust (2) -(headlamp, LHD except Europe, lamps, 1600 and
1600-MK-II) -Fin.(C)105361
3H2962 TC.N.5 Excluder -dust (2) -(headlamp, UK RHD, road lamps, electrical, Twin
Cam)
3H2962 TC.N.5 Excluder -dust (2) -(headlamp, Sweden, road lamps, electrical, Twin
Cam) Com.(C)2418
3H2962 TC.N.5 Excluder -dust (2) -(headlamp Europe LHD, road lamps, electrical, Twin
Cam)
3H2962 TC.N.6 Excluder -dust (2) -(headlamp France LHD, road lamps, electrical, Twin
Cam)
3H2962 TC.N.6 Excluder -dust (2) -(headlamp not UK LHD except Europe, road lamps,
electrical, Twin Cam)
3H2962 TC.N.6 Excluder -dust (2) -(headlamp USA LHD, road lamps, electrical, Twin
Cam) Fin.(C)2277
3H2963 16.J.1 Clip -seal -small (2) (rack assy, steering, 1600 and 1600-MK-II)-
was ACA5118
3H3098 15.N.3 Switch -headlamp and sidelamp
3H3098 16.N.3 Switch -head and sidelamp -(switches, 1600 and 1600-MK-II)
3H3098 TC.N.3 Switch -head and sidelamp -(switches, electrical, Twin Cam)
3H4031 16.M.5 Gasket -body (2) -(headlight, road lamps, 1600 and 1600-MK-II)-
changed to 7H8338 Com.(C)105362 -7H8338 correction was 7H8358
|